Srf m37v manual

Notes on Headphones Road safety Do not use headphones while driving, cycling, or operating any motorized vehicle. Preventing hearing damage Avoid using headphones at high volume. Caring for others Keep the volume at a moderate level. Warning If there is lightning when you are using the unit, take off the headphones immediately. Troubleshooting Should any problem persist after you have made the following checks, consult your nearest Sony dealer.

All buttons do not operate at all. There is hum or noise. Noise occurs. Display is dim, or no indication is displayed. The preset stations may be initialized, if a maintenance service is performed. Please note down your settings in case you want to preset them again.

Accessories Supplied Stereo headphones 1 Belt Clip 1 Design and specifications are subject to change without notice.

Installing the Battery See Fig. A— 1 Open the battery compartment lid and install one size AAA R03 battery not supplied with correct polarity. Battery Life Approx. When to replace the battery You can check the remaining battery power that appears in the display.

Note Do not take more than 3 minutes to replace the battery, otherwise, your clock settings and preset stations will be initialized. A— The battery compartment lid is designed to come off when opened with excessive force.

A Insert the side of the battery first. Size AAA R03 x 1. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. When to replace the battery You can check the remaining battery power that appears in the display. Replace with new battery.

Note Do not take more than 3 minutes to replace the battery, otherwise, your clock settings and preset stations will be initialized. Should that happen, reset the functions again. It can generate heat if the positive and negative terminals of the battery are accidentally come into contact with metallic objects. A Insert the side of the battery first. To attach the battery compartment lid if it is accidentally detached See Fig. To put it back on, see the illustration.

Setting the Clock The display will flash "AM " when the battery is first inserted. The beep sounds and the hour flashes in the display. Each press changes the digit s by one. When you keep the button pressed, the digit s change rapidly. The beep sounds and the minute starts to flash. Repeat step 2 to set the minute. The two beeps sound and the clock starts from 0 seconds.

The channel step of this unit is factory-set to 10 kHz. Change the settings as shown below to be able to listen to the radio.

Two short beeps sound, and the AM channel step will be changed. If you proceed to step 2 again, the channel step changes again. AM: Rotate the unit horizontally for optimum reception. A ferrite bar antenna is built-in the unit See Fig. Under normal conditions, set it to DX.

Playing the Radio -- Manual Tuning 1 Connect the headphones to the i headphones jack. You can return to the previous frequency by pressing BAND. FM1 and FM2 are differentiated only for Preset tuning. For Manual tuning of FM stations, select either band. Each band memorizes the frequency you had tuned previously. Two short beeps sound when the minimum frequency of each band is received during tuning. Presetting a station 1 Follow steps 1 to 4 in "Playing the Radio" and manually tune in to the station you wish to preset.

You will hear two confirmation beeps and preset number appears in the display. To preset another station, repeat these steps. To change the preset station, tune in to the desired station and hold down the preset tuning 1 to 5 button. The new station will replace the previous station on the preset button.

Example: Display window when you preset FM Note Holding down the desired preset tuning button for more than a few seconds will replace the previous station on the preset tuning button with the station you tuned in to. Using the Belt Clip See Fig.

C Use the belt clip when attaching the unit to your belt. To detach the belt clip, see fig. To attach the belt clip, see fig. Please register this product on line at. Proper registration will enable us to send you periodic mailings about. Registering your product will also allow us to contact you in the.

You are cautioned that any changes or modifications not expressly. Operation is subject to the condition that this device does not cause. If you have any questions about this product, you may call:. Slide the HOLD switch so that "-" disappears. Very weak or interrupted sound, or unsatisfactory reception. Display is dim, or no indication is displayed. Preset the station again. The power cannot be turned on, and ".

The preset stations may be initialized, if a maintenance service is. Please note down your settings in case you want to preset them again. Power requirements. Accessories Supplied. Design and specifications are subject to change without notice. See Fig. R03 battery not supplied with correct polarity. When battery is first installed, "AM " flashes in the.

Once the current time is set, the flashing stops. Battery Life Approx. Industries Association standards. The actual battery life may vary. When to replace the battery. You can check the remaining battery power that appears in the display. When the battery becomes exhausted, the unit will turn off. Replace with new battery. Do not take more than 3 minutes to replace the battery, otherwise, your. Should that happen,. Notes on battery.

It can generate heat if the positive and negative terminals of the.