Terrova i pilot manual
Add to Wishlist. Add to Cart. Integrated wireless gps trolling system. Installing i-Pilot link will not extend the warranty of any Minn Kota product it is being installed into or in conjunction with. Free shipping for many products! Cool, Quiet Power: Every Minn Kota lower unit runs cool to extend trolling motor life, and stays quiet.
For customers with special needs, we have provided a customer support phone number reachable 24 hours a day, 7 days a week, days a year: Lock onto spots with … If you are searching for the book Minn kota riptide trolling motor manual in pdf form, in that case you come on to the faithful website.
Take Control with i-Pilot Link. Link lets you control Riptide Ulterra from your Humminbird or its new touch-screen remote. Find the part you need from the schematic, type the part number in our Search Products box, purchase the desired part in the quantity you need! Try up to pounds of thrust. You can equip it with wireless GPS remotes, and stow it effortlessly with the new Lift-Assist mechanism. And stealth? So naturally, we just made it better. A tougher, sleeker new mount houses an arsenal of innovative options.
We have discovered the perfect gross sales for you! Call the shots Fish from anywhere on the boat — even the platform — while keeping your deck free of clutter. Zowel voor zoet als voor zout water. If the trolling motor has AutoPilot it must be removed as follows: a. Remove grommet by pulling back on coil cord strain relief and pushing down on grommet until it pops out.
Review the cables in the head of the trolling motor. If a sonar cable is present, it must be routed around the outer perimeter of the control box. Page 16 7. Route i-Pilot controller cable through grommet hole and through center of coil cord. If AutoPilot was removed, insulate the loose AutoPilot connectors as follows: a.
Page 18 9. Install new grommet supplied with i-Pilot by snapping it into the hole located in front of the coil cord strain relief. The i-Pilot controller cable must be placed in the pass-through slot of the grommet. Place the i-Pilot controller Page 20 Remove center housing by pushing in on both sides and lifting up at the same time. This will expose the main control board and wiring. Page 21 Page 22 Tighten the cable strain relief as shown.
The i-Pilot controller steering cable should slide freely through the strain relief when installed properly. Page 24 Connect the black and white wires from the i-Pilot controller cable to the back and white steering motor wires, making sure black is connected to black and white is connected to white.
Reinstall center housing over control board by pushing it down until the side fi ngers lock into place. Page 27 If a foot pedal is connected to the trolling motor, it must be disconnected. Connect i-Pilot controller cable to the foot pedal connector, making sure the connector nut is tight. If this cannot be done, it is highly recommended that system verifi cation be done in an open area on a calm day with a fully operational outboard motor for a backup means of powering your boat.
When i-Pilot is powered up, it starts to gather satellite information about its location. This minimum level is one bar on the GPs signal icon. Page Knowing Your Remote The remote will automatically turn itself off thirty minutes after the last button press if a learned i-Pilot controller is powered up and within transmitting range. The remote will turn off after three seconds if the i-Pilot controller is powered down or out of transmitting range. Page 32 Remote. Make sure hands are clean, dry and static free.
Learning The i-Pilot remote is prelearned to the controller from the factory. The top of the controller has a single learn button to allow additional remotes to be added to the system. To learn additional remotes: 1. Power up the trolling motor. Page Audio Modes Audio. Modes The i-Pilot Controller also contains an internal speaker which can be programmed to work in two different audio modes. The speaker is programmed to operate in audio mode one from the factory. To enable different audio modes hold down at the same time for three seconds.
Page 36 Power The i-Pilot controller will turn on whenever the trolling motor has power. Connect trolling motor to power. Control functions of i-Pilot. Page Manual. This is not to be confused with the GPs speed which is also displayed on the remote lCd. Page 40 How Do I. Steer the Motor? Control Steer. Left To steer the motor to the left press Steer. Engage High Speed Bypass? Operation Engage Pressing will set the motor speed to maximum immediately.
Disengage Pressing again will set the motor speed to the value it was at previously. Bypass does not enable or disable the prop. Page 42 Tracks are made of many points that i-Pilot records when recording a track. The distance between these points varies based on GPs signal strength and the speed at which you record the track.
When a track is played back, i-Pilot uses the track points and arrival circles to navigate the track. Heading Sensor Instructions. Accessory Compatibility Guide. Trolling Motor Battery Wiring Guide. Terrova Mounting Dimension Guide. Contact Us. Register Products. Software Updates. Compare Now.
Related Products. Rebate Available. Everything you need to know to find the Minn Kota that's right for you. Minn Kota. Old Town. Product Code. As shown MSRP. For Use In. Mounting Location. Motor Style. Max Thrust. Shaft Length. Foot Pedal Style. Power Trim. Power Steering.
0コメント